« previous next »
Pages: « 1 2   Go Down

Author Topic: ebc rotors and sintered pads  (Read 7080 times)

Offline stevewfl

  • Arena
  • Hero Member
  • *****
  • Posts: 4268
  • Country: 00
Re: ebc rotors and sintered pads
« Reply #20 on: February 21, 2013, 07:42:48 PM »
EBC rules  8)
Logged
“The World is a book, and those who do not travel read only a page.” St. Augustine

Offline jamiemac

  • Full Member
  • ***
  • Posts: 605
  • Country: us
Re: ebc rotors and sintered pads
« Reply #21 on: February 21, 2013, 08:21:36 PM »
Quote from: stevewfl on February 21, 2013, 07:42:48 PM
EBC rules  8)
This. Been running them on My bikes as long as I can remember. Pretty sure the first set I installed was on my ZL900 Eliminator, back in 1985.
Logged
2008 C14, Area-P carbon fiber, PCV, Rostra Cruise, LAAM leather seat, Optilux 1500 & MondoMoto MM10 lights, Cee Bailey windshield, BMC air filter, Warm & Safe dual dash mounted heat troller.

Offline VirginiaJim

  • Administrator
  • Elite Member
  • *****
  • Posts: 11365
  • Country: england
  • I've forgotten more than I'll ever know...
    • Kawasaki 1400GTR
Re: ebc rotors and sintered pads
« Reply #22 on: February 22, 2013, 04:00:31 AM »
Quote from: dolomoto on February 21, 2013, 06:40:19 PM
I found the problem...

Glad you found the issue and thanks for giving the update.  We see lots of calls for help and then no feedback as to what the problem/fix really was.
Logged
"LOCTITE®"  The original thread locker...  #11  2020 Indian Roadmaster, ABS, Cruise control, heated grips and seats/w/AC 46 Monitoring with cutting edge technology U.N.I.T is Back! Member in good standing with the Knights of MEH.

Son of Pappy

  • Guest
Re: ebc rotors and sintered pads
« Reply #23 on: February 22, 2013, 07:21:45 AM »
Cheers!!!!!!
Logged

Offline stewart

  • Full Member
  • ***
  • Posts: 296
Re: ebc rotors and sintered pads
« Reply #24 on: February 28, 2013, 07:07:50 PM »
Slightly off topic, but is there a recommended after market pad for stock rotors?
Logged
Stewart
2010 Concours14
COG 9380

Offline Cheesecake

  • Full Member
  • ***
  • Posts: 150
  • Country: us
Re: ebc rotors and sintered pads
« Reply #25 on: February 28, 2013, 09:06:52 PM »
Stick with the Kawa pads unless you have a some reason to change. I used EBC just because I always have, and went back to Kawa pads because of the noise, they make a raspy racket when braking.
Logged
2008 C-14

Offline dolomoto

  • Full Member
  • ***
  • Posts: 137
  • Country: us
  • '08 C14 "Hot, Nasty, Bad-Ass Speed"
Re: ebc rotors and sintered pads
« Reply #26 on: March 02, 2013, 06:35:28 AM »
Quote from: stewart on February 28, 2013, 07:07:50 PM
Slightly off topic, but is there a recommended after market pad for stock rotors?

I use the EBC HH pads with good results. IIRC the OEM front pads went about 25k, replaced by EBC HH pads which went until I changed them when I changed the rotors...so they went about 40k. The OEM rear pads went 56k and were replaced by EBC HH pads also. I change the brake fluid about every year (made easier with SpeedBleeders!)

As to the longevity, I do a lot of highway miles.
Logged
Pages: « 1 2   Go Up
« previous next »